[INFOS]
Title=Canon SX60 Projector
Author=Evan Rowland
Version=1.1.1
DeviceMark=Canon
Model=SX60
Description=LLC for SX60 projector~@~@Commands:~@-Power~@-Input Selection~@-Local/Remote control~@-Auto setup~@-Blank~@-Get Input~@-Flip Display~@-Power Management~@~@Monitoring:~@-Lamp hours ~general range of lamp usage~@~@Notes:~@For blank to turn off bulb, first set power management to standby.
[TYPE]
Communication=Serial
Baud rate=19200
Data size=8
Stop bits=2
Parity=0
DTR control=0
RTS control=0
Full duplex=1
DTR Duplex=0
DTR handshake=0
DSR out flow=0
RTS handshake=0
CTS out flow=0
Break character=_
Break time=2
[FRAMES]
Count of bytes=0
Hexa character=!
Decimal character=&
Header character=
Ending character=
Convert non literal mode=0
Keep frames=0
Input checksum verification=0
Output checksum verification=1
Checksum character=@
Timeout between bytes=250
[EXCLUDED CHARACTERS]
Count=0
Not in header/ending=1
Checksum before replacement=0
[CHECKSUM]
Checksum type=SUM
CRC16 mask=A001
CRC16 initial value=0000
Start checksum at=0
Stop checksum from=
Checksum count=1
Checksum position from end=
Checksum two's complement=0
Checksum ASCII coded=0
Checksum high byte first=1
[COMMANDS]
Count=8
Command0.Name=Power
Command0.Frame=POWER [Power,enum,literal,0,2,on,off,ON,OFF]!0D
Command1.Name=Input selection
Command1.Frame=INPUT=[Input,enum,literal,0,8,D-RGB,A-RGB1,A-RGB2,COMP,VIDEO,S-VIDEO,D-VIDEO,SCARTRGB,D-RGB,A-RGB1,A-RGB2,COMP,VIDEO,S-VIDEO,D-VIDEO,SCARTRGB]!0D
Command2.Name=Control
Command2.Frame=[Control device,enum,literal,0,2,Showmaster,Remote/buttons,REMOTE,LOCAL]!0D
Command3.Name=Auto Setup
Command3.Frame=AUTOSETEXE [auto set,enum,literal,0,4,FOCUS,Vertical Keystone,screen color correction,input,FOCUS,VKS,SCRN,INPUT]!0D
Command4.Name=Blank
Command4.Frame=BLANK=[on/off,enum,literal,0,2,On,Off,ON,OFF]!0D
Command5.Name=Get Input
Command5.Frame=GET INPUT!0D
Command6.Name=Flip Display
Command6.Frame=IMAGEFLIP=[mounted posistion,enum,literal,0,4,None,Ceiling,Rear,rear ceiling,NONE,CEILING,REAR,REAR_CEILING]!0D
Command7.Name=Power Management
Command7.Frame=PMM=[mode,enum,literal,0,3,Off,Standby,Exit,OFF,STANDBY,EXIT]!0D
[POSITRACK GROUPS]
Count=0
[ANSWERS]
For each mode=1
For each frame=
Count=0
[MONITORING]
FixedLengthChar=X
VariableLengthChar=?
Requests count=2
Request.0=?POWER!0D
RequestPeriod.0=9000
RequestLink.0=
Request.1=GET LAMPCOUNTER!0D
RequestPeriod.1=1000
RequestLink.1=
Wait for answer=0
Timeout Answer=3000
Variables count=2
Variable0.Name=Power_Status
Variable0.Frame=g:POWER=?!0D
Variable0.Position=8
Variable0.Length=1
Variable0.Type=enum
Variable0.Format=literal
Variable0.UpdateMode=0
Variable0.EnumNameCount=2
Variable0.EnumName0=on
Variable0.EnumValue0=ON
Variable0.EnumName1=off
Variable0.EnumValue1=OFF
Variable0.BEnumIntegerValues=0
Variable1.Name=Lamp_Counter
Variable1.Frame=g:LAMPCOUNTER=?
Variable1.Position=14
Variable1.Length=1
Variable1.Type=enum
Variable1.Format=literal
Variable1.UpdateMode=0
Variable1.EnumNameCount=8
Variable1.EnumName0=0-459 hours
Variable1.EnumValue0=[G_______]
Variable1.EnumName1=460-919 hours
Variable1.EnumValue1=[GG______]
Variable1.EnumName2=920-1379 Hours
Variable1.EnumValue2=[GGG_____]
Variable1.EnumName3=1380~1839 hours
Variable1.EnumValue3=[GGGG____]
Variable1.EnumName4=1840~2299 hours
Variable1.EnumValue4=[GGGGG___]
Variable1.EnumName5=2300~2399 hours
Variable1.EnumValue5=[GGGGGY__]
Variable1.EnumName6=2400~2499 hours
Variable1.EnumValue6=[GGGGGYY_]
Variable1.EnumName7=2500~???? hours
Variable1.EnumValue7=[GGGGGYYR]
Variable1.BEnumIntegerValues=0
[AUTOMATION]
Connection mode=1
Deconnection mode=1
Deconnection delay=20